قابل توجه دارندگان Laptop HP
سلام بلاخره بعد از جند مدت تونستم مشكل نصب ويندوز XP در labtop خودم كه مدلش pavilion dv6000 بود را رفع كنم و را حلش را از سايت HP كرفتم
There are three methods for installing a SATA drive a Windows installation.
- [ برای مشاهده لینک ، با نام کاربری خود وارد شوید یا ثبت نام کنید ]
- [ برای مشاهده لینک ، با نام کاربری خود وارد شوید یا ثبت نام کنید ]
- [ برای مشاهده لینک ، با نام کاربری خود وارد شوید یا ثبت نام کنید ]
Disable the native-SATA in the BIOS
If the BIOS provides an option to disable the native-SATA configuration in the BIOS, do the following steps.
- Turn off the computer.
- Press the power button and press f8 to open the BIOS Setup.
- Use the cursor to navigate the Configuration options to locate the Native-SATA setting.
- If there is a SATA setting, select the Disable option, and then press F10 to save the change and restart the computer.
- If there is no SATA setting, use one of the other options in this document to change the settings.
Stand Alone Windows Installation
This procedure uses third-party software and is typically performed by home PC users.
- Determine the type of processor in the computer, then search for and download the latest SATA AHCI driver from the processor manufacturer's web site. Some SATA AHCI drivers are available on the [ برای مشاهده لینک ، با نام کاربری خود وارد شوید یا ثبت نام کنید ] web site. For additional information, [ برای مشاهده لینک ، با نام کاربری خود وارد شوید یا ثبت نام کنید ] .
- Download and install an orthodox file manager.
NOTE: For this example, [ برای مشاهده لینک ، با نام کاربری خود وارد شوید یا ثبت نام کنید ] is used. Refer to the software help files for additional assistance.- Download and install the CD/DVD data recovery software.
NOTE: For this example, [ برای مشاهده لینک ، با نام کاربری خود وارد شوید یا ثبت نام کنید ] is used. Refer to the software help files for additional assistance.
Extracting files
- Start Total Commander by clicking Start , All Programs , Total Commander and then click Total Commander 32 . If the non-registered version is used, follow the pop-up Windows instructions. NOTE: For assistance and instructions on using Total Commander, view the Total Commander help file.
- Locate the downloaded SATA AHCI driver using the directory structure in Total Commander. Select the SATA AHCI driver.
Figure 1: SATA AHCI driver located
- On the File Menu, click File and select Unpack Specific Files .
- Type the target location to unpack the file.
Figure 2: Enter unpack location
- Locate the unpacked files.
- Repeat the unpack process for F6flpy32.exe .
- Open the temp.IMA extracted from the F6flpy32.exe file using Ultra ISO or equivalent application.
Figure 3: temp.IMA driver files
- Copy the temp.IMA driver files to a floppy disk or burn the files to a CDROM.
Disable SATA native mode
NOTE: This option is not available in the BIOS on Vista models.
- Start the notebook PC.
- Repeatedly press the F10 key (or key designated by the notebook PC) until the notebook enters the Computer Setup screen.
- Use the arrow keys to select System Configuration .
- Use the arrow keys to select SATA Native Mode and set the mode to Disable .
Figure 4: Disable SATA Native Mode
- Press the F10 key (or designated key to accept the changes).
- Save changes and exit Computer Setup.
- The notebook should restart.
Installing Windows using native SATA drivers
To install Windows XP with native SATA driver, perform the following steps:
- Boot the notebook PC.
- Insert the Windows XP installation CD into the optical CD/DVD drive.
- Press the F6 key when prompted.
Figure 5: Third Party Driver Prompt
- Press the S key to specify the additional device.
Figure 6: Specify Additional Device
- Insert the SATA driver disk into drive A.
Figure 7: Insert Driver Disk
- Follow the on-screen prompts.
Enable SATA native mode
- During the starting of the notebook PC, repeatedly press the F10 key (or key designated by the notebook PC) until the notebook enters the Computer Setup screen.
- Use the arrow keys to select System Configuration .
- Use the arrow keys to select SATA Native Mode and set the mode to Enable .
Figure 8: Enable SATA native mode
- Press the F10 key (or designated key to accept the changes).
- Save changes and exit Computer Setup.
- The notebook should restart.
RIS (Remote Installation Services)
This procedure is typically performed by IT professionals over a network.
- Download the latest “Intel Matrix Storage Manager” driver After downloading the “Intel Matrix Storage Manager” create one folder named Sata and copy the iata61_enu.exe which you just downloaded from above mentioned link. Intel Matrix Storage Manager also includes SATA controller driver.
- Use following command to extract the driver files:
c:\sata\ iata61_enu.exe -a -a -pc:\sata
When run, the installation process begins; simply click through the dialogs as prompted. This will not install the driver, it will only extract the driver files to <c:\sata>. After the extraction is completed, the driver files can be found in <c:\sata\Driver>.- Copy the extracted files to the RIS distribution point (on the RIS server):
RemoteInstall\Setup<Language>\Images\<Dir_Name>\i3 86- Copy the same files to:
RemoteInstall\Setup<Language>\Images\<Dir_Name>\$o em$\$1\drivers\sata- Open the RemoteInstall\Setup<Language>\Images\<Dir_Name>\i3 86\txtsetup.sif file with notepad, and add the following lines to the sections noted (section names are in brackets):
- Save the file and exit notepad.
- Open the Remote Install\Setup\<Language>\Images\<Dir_Name>\i386\te mplates\ristndrd.sif file with notepad, and under the section [Unattended] add the following lines:
- Save the file and exit notepad.
- Finally, to complete the process, stop and restart the BINL service on the RIS server as follows:
Go to a command prompt and type net stop binlsvc and press Enter. Then type net start binlsvc and press Enter.
The RIS installation point has now been updated with the SATA driver.
توضيحات بالا بصورت انكليسي بود اما 3 تا راه را نشون داده كه شما هارد ساتا را به ويندوز معرفي كنيد راه اولش راهي بود كه من انتخاب كردم و جواب داد اين بود كه من وارد bios setup شدم و كزينهNative-SATA setting را disable كردم و خيلي راحت ويندوز XP هارد منو شناخت حالا هر كس راجع به اين مسله سوالي داره همين جا ببرسه ممنون
جواب بصورت نقل قول