درايو من هم Philips Lite-On هست و كنسولم ماله 07/2009 هست . ولي من بعد از كپي خور كردن كنسول و آپديت كردنش تا حالا نيازي به ديسك اكتيو پيدا نكردم . اين بازيهاي جديد رو هم اجرا كردم : TEKKEN6 - CODMW2 - Assisans Creed 2 و........ كلي بازي ديگه .
درايو من هم Philips Lite-On هست و كنسولم ماله 07/2009 هست . ولي من بعد از كپي خور كردن كنسول و آپديت كردنش تا حالا نيازي به ديسك اكتيو پيدا نكردم . اين بازيهاي جديد رو هم اجرا كردم : TEKKEN6 - CODMW2 - Assisans Creed 2 و........ كلي بازي ديگه .
احتمالا ديسك هاي شما به Wave 3 تبديل شده اند؛ چون اين بازي ها در Wave 4 ارائه شده اند.
الان به روش سخت افزاري كپي خور ميشه ومثل اينكه بين 40 تا 60 هزار هم هزينه داره!
روش كار هم به صورت زيره:
The only difference between my method and MRA's is that he instructs people to cut "pad101" away from the trace. The problem is that this is not that easy for most people. After you do it his way the pad is very weak. Many people broke the pad off while cutting it from the trace and others damaged it after when they heated it up to solder. So I came up with a 3 cut & 2 jump method that I think is much safer for the average user. Also he has the Ground point going to a tiny pad when most of the circuit board is Ground.
Also i have included some very high quality pictures that show every step in great detail.
Instructions (also by MRA i changed a few words)
-Switch in closed postion (on) (position 1 on MRA's diagram)
-power drive
-start dosflash --> spi should get discovered with status 0x72
-Flip switch to open position (off) (position 2 on MRA's diagram)
-click READ
-If you have a Winbond SPI Flash inside (i know, you can´t be sure about this from the outside) you will probably get status 0x72 but instead of recognizing the Winbond flash it will be recognized as unknown flash chip (manufacturer and device ID 0xFF). If that is the case you can´t use Dosflash anymore, you have to use JF!
-start JF
-put the switch in position 1 (ON)
-power drive
-in the MTKFlash Tab click "intro"
-it shoudl get "recognized" as unknown flash chip with status 0x72 like it was in Dosflash
-put switch in position 2 (OFF)
-click onto "intro" again
-now JF should recognize the Winbond SPI with status 0x72 and you can dump the whole drive
IMPORTANT: Don´t power the drive down between the 2 intros!
Last edited by name; 09-12-2009 at 11:49.
فكر نكنم به خاطر تبديل باشه كه كنسول من اجرا ميكنه . به احتمال زياد به خاطر آپديتي هست كه دوستم برام انجام داد . اخه اون كارش اينه و گفت اين اپديت تازه اومده و همه بازيهاي موجود (جديد) رو اجرا ميكنه .
آخه نميشه كه من اين همه بازي مختلف گرفته باشمو همش تبديل شده باشند ولي اكثر بچه ها بازيهايي رو كه ميگيرن Wave 4 باشه و ديسك اكتيو بخواد .
الان 15 تا 20 هزار ميگيرن كه اين آپديت جديده رو بريزن .
من هیچی در مورد Xbox نمی دونم.
برم یه دونه xbox 360 بخرم میتونم باهاش فیلم ببینم؟
فیلم DivX و mkv رو ؟
شما پست اول همین تاپیک رو بخون همه چی دستت میاد
divX اره اما Mkv نه ( هنوز هیچ player نیومده براش )
WD TV HD Media Player میتونه فرمت MKV رو پخش کنه !!!
کد:برای مشاهده محتوا ، لطفا وارد شوید یا ثبت نام کنید
خب دوستان دسته دیگه از کار افتاد....چراغ وسطیش که اصلا روشن نمیشه...
هر کاری هم که به فکرم میرسید کردم نشد...
بازش کردم پاکش هم کردم ..باز نشد با اوومتر امتحان کردم برق باطری میرسه پس مشکل از اونجاش نباشه احتمالا IC رفته اون دنیا...
خیلی دوسش داشتم حیف شد.
good for you
پدرام چجوری می تونم بهت پیغام بدم؟دلم واست تنگ شده بابا!!!
هم اکنون 2 کاربر در حال مشاهده این تاپیک میباشد. (0 کاربر عضو شده و 2 مهمان)