ممکنه وقتی داشتین اسم فایل رو میذاشتین اشتباهن پسوند فایل رو هم تغییر داده باشین.احتمال داره پسوند درست docx باشه که شما اشتباهن doc گذاشتین.
در ضمن ورژنهای خیلی قدیمی ورد فایلهای docx رو نمیشناسه و یه پیام شبیه این میده.
ممکنه وقتی داشتین اسم فایل رو میذاشتین اشتباهن پسوند فایل رو هم تغییر داده باشین.احتمال داره پسوند درست docx باشه که شما اشتباهن doc گذاشتین.
در ضمن ورژنهای خیلی قدیمی ورد فایلهای docx رو نمیشناسه و یه پیام شبیه این میده.
Last edited by paveej; 19-02-2016 at 19:44.
این روش شما رو خوندم انشالله که جواب بگیریم از این روش. اما خب طبق آموزش داده شده، باید فایل رو در همون سیستمی که ایجاد کردیم باز کنیم. چون باید به مسیر نصب نرم افزار word در سیستمی که فایل در اون ایجاد شده رفتمن یه راه دیگه به ذهنم میرسه و اون اینه که برید فایل رو ریکاوری کنید از طریق خود ورد
که نتیجه این فردا مشخص می شه. باز هم ممنون
نه دوست عزیزممکنه وقتی داشتین اسم فایل رو میذاشتین اشتباهن پسوند فایل رو هم تغییر داده باشین.احتمال داره پسوند درست docx باشه که شما اشتباهن doc گذاشتین.
در ضمن ورژنهای خیلی قدیمی ورد فایلهای docx رو نمیشناسه و یه پیام شبیه این میده.
همکار من، مطمئن هست که با این پسوند ذخیره کره. چون می خوان به فایل هاشون در هر سیستمی دسترسی داشته باشن، همیشه فایل ها رو با فرمت doc ذخیره می کنن
چطور میشه یه عکس رو کنار متن قرار داد به سادگی؟ میخوام تو word 2010 اینکار رو بکنم یا متن بهم میریزه یا عکس. چیزی که میخوام اینه:
![]()
عکس رو وارد کنین روش کلیک کنین، از تب Layout گزینه Wrap Text رو بزنین و Top and Bottom متن رو هم با Text Box بنویسین.
سلام
از قسمت View گزینه Ruler رو فعال کنین
بعد اگر بخواین هم میتونین اعداد رو به متن نزدیک کنین و یا میتونین متن رو به عدد نزدیک کنین
![]()
سلام
من تو ورد مثلا عدد 222.3 رو تایپ میکنم میزنه 222,3 البته اعداد فارسی رو . تو تنظیمات قسمت language روی hindi هست.
در واقع ویرگول میزنه به جای نقطه چجوری میشه درستش کرد ؟؟
سلام
دوستان من تایپ فارسی که در ورد 2007 میکنم. به جای اینکه بره جلو
از عقب پیشرفت میکنه در تایپ کردن![]()
کسی راه حلی نداره برای این مشکل؟
چیکار کنم؟
This error usually occurs because of macro security settings. If you know that the macro comes from a source that you trust, you can change your macro security settings to allow you to enable the macro. The way that you change your macro security settings depends on the Microsoft Office System program that you are using.
Microsoft Office Access, Microsoft Office Excel, Microsoft Office PowerPoint, or Microsoft Office Word --
To check your macro security settings, click the Microsoft Office Button, click <program name> Options, click Trust Center, and then click Trust Center Settings.
If macro security is set to Disable all macros without notification, all macros are automatically disabled. Use the following procedure to enable the macro.
In the Trust Center dialog box, click Macro Settings, and then click Disable all macros with notification.
Click OK in the Trust Center dialog box to apply the new setting. Click OK to close the program options dialog box.
Close the file and the Microsoft Office program that you are using.
Open the file again. A Security Alert appears in the Document Information Bar just below the ribbon. Click Enable Content to allow the macro to run.
When you have enabled the macro, it is recommended that you return the macro security setting to Disable all macros without notification.
If macro security is set to Disable all macros with notification, but you selected Disable when prompted by the macro warning dialog when you opened the file, use the following procedure to enable the macro.
In the Trust Center dialog box, click Cancel. Click Cancel to close the program options dialog box.
Close the file and the Microsoft Office program that you are using.
Open the file again. A Security Alert appears in the Document Information Bar just below the ribbon. Click Enable Content to allow the macro to run.
If macro security is set to Disable all macros except digitally signed macros, the macro may not have been digitally signed. Verify that you can trust the macro before using the following procedure to allow it to run.
In the Trust Center dialog box, click Cancel. Click Cancel to close the program options dialog box.
Close the file and the Microsoft Office program that you are using.
Open the file again. A Security Alert appears in the Document Information Bar just below the ribbon. Click Enable Content to allow the macro to run
دوستان اگه کسی میدونه با این ارور باید چیکار کرد خواهشا راهنمایی کنه . بدجور گیرم![]()
هم اکنون 1 کاربر در حال مشاهده این تاپیک میباشد. (0 کاربر عضو شده و 1 مهمان)