Printable View
خوب فایل rpm رو دانلود می کردی . از یکی از این دوسایت با توجه به مدل مودمت ( hcf یا hsf ) و با توجه به نوع توزیع و ورژن کرنلت فایل مورد نظر را دانلود کن.نقل قول:
کد:http://www.linuxant.com/drivers/hcf/full/downloads.php
کد:http://www.linuxant.com/drivers/hsf/full/downloads.php
سلام
لطف کنید بگین چیپست مودم من چیه و ایا درایورش در دسترس هست؟
تشکر از لطفتون.
Vendor 8086h Intel Corporation
Device 27D2h Unknown
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 01h, Header Type 81h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 64 Bytes (16 DWords)
PCI Class Bridge, type PCI to PCI
System IRQ 17, INT# B
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 16, Subordinate Bus Number 16
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 2000h (Received Master Abort, Fast Timing)
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : F4000000h to F40FFFFFh
Prefectchable Memory Range Passed to Secondary Bus : None
New Capabilities List Present:
PCI Express Capability, Version 1
Device/Port Type : Root port of PCI Express Root Complex
Port is an Expansion Slot
Unsupported Request Severity is Non-Fatal
AUX Power Detected
Maximum Link speed : 2.5Gb/s
Maximum Link Width : x1
Link Port Number : 2
Common Clock Configuration In Use
Current Link speed : 2.5Gb/s
Current Link Width : x1
Hot Plug Surprise is Possible
Hot Plug Capable
Physical slot Number 0
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 32-bit addresses
Subsystem ID & Subsystem Vendor ID Capability
SSVID : 103Ch
SSID : 30A2h
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Vendor 8086h Intel Corporation
Device 27D6h Unknown
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 01h, Header Type 81h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 64 Bytes (16 DWords)
PCI Class Bridge, type PCI to PCI
System IRQ 19, INT# D
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 32, Subordinate Bus Number 32
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 2000h (Received Master Abort, Fast Timing)
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 2000h to 3FFFh (16-bit)
Memory Range Passed to Secondary Bus : F0000000h to F3FFFFFFh
Prefectchable Memory Range Passed to Secondary Bus : None
New Capabilities List Present:
PCI Express Capability, Version 1
Device/Port Type : Root port of PCI Express Root Complex
Port is an Expansion Slot
Unsupported Request Severity is Non-Fatal
AUX Power Detected
Maximum Link speed : 2.5Gb/s
Maximum Link Width : x1
Link Port Number : 4
Asynchronous Clocking in Use
Current Link speed : 2.5Gb/s
Current Link Width : x0
Hot Plug Surprise is Possible
Hot Plug Capable
Physical slot Number 0
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 32-bit addresses
Subsystem ID & Subsystem Vendor ID Capability
SSVID : 103Ch
SSID : 30A2h
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Vendor 8086h Intel Corporation
Device 27C8h Unknown
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 4 is an I/O Port : 00004020h
System IRQ 20, INT# A
Vendor 8086h Intel Corporation
Device 27C9h Unknown
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 4 is an I/O Port : 00004040h
System IRQ 17, INT# B
Vendor 8086h Intel Corporation
Device 27CAh Unknown
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 4 is an I/O Port : 00004060h
System IRQ 18, INT# C
Vendor 8086h Intel Corporation
Device 27CBh Unknown
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 4 is an I/O Port : 00004080h
System IRQ 19, INT# D
Vendor 8086h Intel Corporation
Device 27CCh Unknown
Command 0006h (Memory Access, BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timin
g)
Revision 01h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial, type USB 2.0 (EHCI)
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 0 is a Memory Address (anywhere in 0-4Gb) : F4584000h
System IRQ 20, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
USB 2.0 EHCI Debug Port Capability
Vendor 8086h Intel Corporation
Device 2448h 82801BAM/CAM/DBM (ICH2-M/3-M/4-M) Hub Interface to PCI Bridge
Command 0107h (I/O Access, Memory Access, BusMaster, System Errors)
Status 0010h (Has Capabilities List, Fast Timing)
Revision E1h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI (Subtractive Decode)
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 2, Subordinate Bus Number 3
Secondary Bus Command 0006h (ISA mapping)
Secondary Bus Status 2280h (Supports Back-To-Back Trans., Received Master Abo
rt, Medium Timing)
Secondary Bus Latency 20h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : F4100000h to F43FFFFFh
Prefectchable Memory Range Passed to Secondary Bus : None
New Capabilities List Present:
Subsystem ID & Subsystem Vendor ID Capability
SSVID : 103Ch
SSID : 30A2h
Vendor 8086h Intel Corporation
Device 27B9h Unknown
Command 0107h (I/O Access, Memory Access, BusMaster, System Errors)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 01h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
New Capabilities List Present:
Vendor-Dependant Capability
Vendor 8086h Intel Corporation
Device 27C4h Unknown
Command 0005h (I/O Access, BusMaster)
Status 02B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back Tran
s., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 0 is an I/O Port : 00000000h
Address 1 is an I/O Port : 00000000h
Address 2 is an I/O Port : 00000000h
Address 3 is an I/O Port : 00000000h
Address 4 is an I/O Port : 000040A0h
System IRQ 11, INT# B
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D3hot
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
Vendor 104Ch Texas Instruments (TI)
Device 8039h Unknown
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 00h, Header Type 82h, Bus Latency Timer 40h
Self test 00h (Self test not supported)
Cache line size 64 Bytes (16 DWords)
PCI Class Bridge, type PCI to Cardbus
System IRQ 18, INT# A
PCI bus number 2, CardBus bus number 3, Subordinate bus number 3
CardBus latency 00h
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
Vendor 104Ch Texas Instruments (TI)
Device 803Ah Unknown
Command 0006h (Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 40h
Minimum Bus Grant 02h, Maximum Bus Latency 04h
Self test 00h (Self test not supported)
Cache line size 64 Bytes (16 DWords)
PCI Class Serial, type OHCI FireWire
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 0 is a Memory Address (anywhere in 0-4Gb) : F4101000h
Address 1 is a Memory Address (anywhere in 0-4Gb) : F4104000h
System IRQ 19, INT# B
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
Vendor 14E4h Broadcom Corp
Device 170Ch BCM440x 100Base-TX Fast Ethernet
Command 0000h (Bus Access Disabled!!)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 02h, Header Type 00h, Bus Latency Timer 40h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 30A2103Ch BCM440x 10/100 Integrated Controller (Guess Only!)
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 0 is a Memory Address (anywhere in 0-4Gb) : F4108000h
System IRQ 10, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D3hot (Device off: no power to device, maximum power
saving)
IRQ Summary: IRQs 10,11,14,15,16,17,18,19,20 are used by PCI devices
Shared IRQs: IRQ 16 is shared by 3 PCI Devices
IRQ 17 is shared by 2 PCI Devices
IRQ 18 is shared by 2 PCI Devices
IRQ 19 is shared by 3 PCI Devices
IRQ 20 is shared by 2 PCI Devices
IRQ control is currently managed by the system APIC controller - IRQ info is
not actual hardware settings...
NT: Close driver : Operation was successful
NT: Open SCM : Operation was successful
NT: Stop driver : Operation was successful
NT: Remove driver : Operation was successful
NT: Close SCM : Operation was successful
من مي خواهم با مودم Siemens به اينترنت ADSL وصل شم
ولي زياد با لينوكس آشنايي ندارم اگه ميشه راهنمايي يا
آموزش نصب مودم و راه اندازيشو بگيد خيلي ممنون
سلامنقل قول:
اگر مودم شما پورت lan داره کافیه که IP رو تنظیم کنید بهتره که نوع توزیع مورداستفاده هم بگید تا بهتر بشه کمک کرد
با سلام.نقل قول:
اگه ميشه اسم و مدل مدمو بزارين چون منم مي خوام مودم بگيرم ولي نمي دونم چه مودمي براي ADSL تو لينوكس خوبه.
بعد هم مراحل كامل شناسي مودم USB و تنظيم IP در لينوكس رو بزارين.:10:
نقل قول:
بله پورت lan و usb داره
"نوع توزیع مورداستفاده" يعني چي؟
به هر نسخه از لینوکس یک توزیع گفته میشه. یعنی اسم لینوکستون چیه ؟ فدورا , سوسه ,اوبونتو و ...نقل قول:
نقل قول:
كارامد (فارسي) ولي فكر كنم از گنو تبديل شده باشه
البته کاآمد از نسخه ی Slax که خود بر پایه ی Slackware درست شده، و در واقع صرفا فارسی شده.نقل قول:
البته می دوونم جاش نیست ولی می خواستم ببینم دوستمون که از این توزیع استفاده می کنه راضی هست و چرا این توزیع رو انتخاب کرده؟:20:
من چون ويندوز هم دارم بيشتر از
ويندوز استفاده مي كنم و تازه مي خواهم
با هاش كار كنم ولي فكر نكنم نسخه خوبي
باشه تا حالا چند دفعه گير كردم نتونستم
كاري بكنم البته شايدم براي ناشي بودن بنده باشه