با سلام
rootnt عزیز باتشکر فراوان از شما استاد گرانقدر ، بالاخره مودم نصب وفعال شد.
ولی متاسفانه بعد از کانکت شدن هر صفحه ای رو که باز میکنم پیغام server not found میده .
Printable View
با سلام
rootnt عزیز باتشکر فراوان از شما استاد گرانقدر ، بالاخره مودم نصب وفعال شد.
ولی متاسفانه بعد از کانکت شدن هر صفحه ای رو که باز میکنم پیغام server not found میده .
سلام
خواهش می کنم
از کجا متوجه می شید کانکت شده؟
کارت شبکه دارید که فعالش کردید؟
سلام
حقیقتش اطمینان ندارم.چون مثل ویندوز خودش رو نشون نمیده.
ping هم نکردم چون اصلا نمی دونم در لینوکس چطور میشه این کار رو کرد.
فقط در حد همون شماره گیری مودم وسر وصدای اتصال به سرور.
سلام
دستور ping که هیچ فرقی بین لینوکس و ویندوز نداره
شما ترمینال رو باز کنید و ping x.x.x.x
یه روشی هم هست برای اینکه متوجه وصل شدن به اینترنت بشید
وقتی که فکر کردید به اینترنت وصل شدید روی پنل (بالایی یا پایینی فرقی نمی کنه) کلیک راست کنید و Add to panel رو انتخاب کنید بعد از اون لیست network monitor روانتخاب کنید
بعد یه آیکون (۲تا مونیتور) تقریبا مثل همون ویندوزه فقط رنگش فرق داره میاد روی پنل
فقط برای اطمینان روش کلیک راست کنید و properties رو بزنید در صفحه ای که باز می شه در فیلد name باید ppp0 انتخاب شده باشه
من از مودم پاراداین (Paradyne) استفاده میکنم
الان یک ماهی میشه که دنبال درایورش برای لینوکس اوبونتو هستم ولی پیداش نمیکنم
کسی اینجا میتونه کمکی کنه در این زمینه؟
ممنون
سلام
پست اول همين تاپيك رو بخونيد
اون برنامه ای که برای شناخت نوع مودم بود (pci32) رو وقتی اجرا میکنم صفحه command prompt اجرا میشه و سریع بسته میشهنقل قول:
چیکار باید بکنم؟
در ضمن مودمم اکسترنال و با usb هستش
ممنون
دوست عزیز من با مودم zoltix موشکل دارم لطفا راهنمایی کنید
zoltrix smart spirit
با چیپست conexant
سلام
parsbin جان در اين تاپيك بارها گفتم
اول command prompt رو باز كنيد و با اون برنامه pci32 رو اجرا كنيد اينطوري ديگه بسته نمي شه
آقا مسعود پست اول همين تاپيك رو بخونيد
خوب درست شدنقل قول:
ولي چيزي سر در نياوردم ازش!
اين خروجي همون برنامه اس
دو تا مودم هم الان رو سيستم دارم.يكي 56 كيلوبيت دايال آپ و يكي هم براي adsl
دومي رو هم ميخوام نصب كنم
کد:D:\p>pci32.exe
NT: Open SCM : Operation was successful
NT: Install driver : Service already exists
NT: Start driver : Operation was successful
NT: Close SCM : Operation was successful
NT: Open Driver : Operation was successful
Craig Hart's PCI+AGP bus sniffer, Version 1.1, freeware made in 1996-2005.
Searching for PCI Devices using Configuration Mechanism 1 [NT/2K/XP/etc Method]
Vendor 1106h VIA Technologies Inc
Device 0601h VT8601 Apollo PLE133 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status A290h (Has Capabilities List, Supports Back-To-Back Trans., Received Mas
ter Abort, Detected Parity Error, Medium Timing)
Revision 05h, Header Type 00h, Bus Latency Timer 08h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Address 0 is a Memory Address (anywhere in 0-4Gb, Prefetchable) : E0000000h
New Capabilities List Present:
AGP Capability, Version 2.0 (AGP 4x and below support)
AGP Speed(s) Supported : 1x 2x 4x
FW Transfers Supported : No
>4Gb Address Space Supported : No
Sideband Addressing Supported : Yes
Maximum Command Queue Length : 8 bytes
AGP Speed Selected : 4x
FW Transfers Enabled : No
>4Gb Address Space Enabled : No
AGP Enabled : Yes
Sideband Addressing Enabled : Yes
Current Command Queue Length : 1 byte
Vendor 1106h VIA Technologies Inc
Device 8601h VT82C601 Apollo PLE133 CPU to AGP Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status A230h (Has Capabilities List, Supports 66MHz, Received Master Abort, Det
ected Parity Error, Medium Timing)
Revision 00h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus Number 1
Secondary Bus Command 000Ch (ISA mapping, VGA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : E4000000h to E6FFFFFFh
Prefectchable Memory Range Passed to Secondary Bus : None
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Vendor 1106h VIA Technologies Inc
Device 0686h VT82C686B PCI to ISA Bridge
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 40h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID 00001106h VT82C686/A PCI to ISA Bridge
Subsystem Vendor 1106h VIA Technologies Inc
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Vendor 1106h VIA Technologies Inc
Device 0571h VT82xxxx EIDE Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timin
g)
Revision 06h, Header Type 00h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID 05711106h VT82Cxxxx EIDE Controller (All VIA Chipsets) (Generic ID
)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000C000h
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Vendor 1106h VIA Technologies Inc
Device 3038h VT82C686B USB Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 1Ah, Header Type 00h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB (UHCI)
Subsystem ID 12340925h VIA USB Controller
Subsystem Vendor 0925h Known Bad Subsystem ID - no Vendor ID Available
Address 4 is an I/O Port : 0000C400h
System IRQ 11, INT# D
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Vendor 1106h VIA Technologies Inc
Device 3038h VT82C686B USB Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 1Ah, Header Type 00h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB (UHCI)
Subsystem ID 12340925h VIA USB Controller
Subsystem Vendor 0925h Known Bad Subsystem ID - no Vendor ID Available
Address 4 is an I/O Port : 0000C800h
System IRQ 11, INT# D
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Vendor 1106h VIA Technologies Inc
Device 3057h VT82C686B ACPI Power Management Controller
Command 0000h (Bus Access Disabled!!)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timin
g)
Revision 40h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other
Subsystem ID 30571106h VT82C686/A/B ACPI Power Management Controller (Generic I
D)
Subsystem Vendor 1106h VIA Technologies Inc
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Vendor 1106h VIA Technologies Inc
Device 3058h VT82C686B AC'97 Audio Codec
Command 0001h (I/O Access)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 50h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID A0021458h Onboard AC'97 Audio Codec
Subsystem Vendor 1458h Giga-Byte Technology
Address 0 is an I/O Port : 0000CC00h
Address 1 is an I/O Port : 0000D000h
Address 2 is an I/O Port : 0000D400h
System IRQ 5, INT# C
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Vendor 10ECh Realtek Semiconductor
Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
Command 0005h (I/O Access, BusMaster)
Status 8290h (Has Capabilities List, Supports Back-To-Back Trans., Detected Par
ity Error, Medium Timing)
Revision 10h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 20h, Maximum Bus Latency 40h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 813910ECh RT8139 (A/B/C/810x) Fast Ethernet Adapter (Generic ID)
Subsystem Vendor 10ECh Realtek Semiconductor
Address 0 is an I/O Port : 0000E000h
Address 1 is a Memory Address (anywhere in 0-4Gb) : E7010000h
System IRQ 11, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D1, D2, D3hot, D3cold
PME# signalling is currently enabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Vendor 1023h Trident Microsystems
Device 8500h CyberBlade/i1
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 02B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back Tran
s., Medium Timing)
Revision 6Ah, Header Type 00h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Subsystem ID 40001458h VT8361/VT8601 Graphics Controller (Guess Only!)
Subsystem Vendor 1458h Giga-Byte Technology
Address 0 is a Memory Address (anywhere in 0-4Gb) : E5800000h
Address 1 is a Memory Address (anywhere in 0-4Gb) : E6000000h
Address 2 is a Memory Address (anywhere in 0-4Gb) : E5000000h
System IRQ 10, INT# A
Expansion ROM of 64Kb decoded by this card (Currently disabled)
New Capabilities List Present:
AGP Capability, Version 2.0 (AGP 4x and below support)
AGP Speed(s) Supported : 1x 2x 4x
FW Transfers Supported : No
>4Gb Address Space Supported : No
Sideband Addressing Supported : Yes
Maximum Command Queue Length : 33 bytes
AGP Speed Selected : 4x
FW Transfers Enabled : No
>4Gb Address Space Enabled : No
AGP Enabled : Yes
Sideband Addressing Enabled : Yes
Current Command Queue Length : 8 bytes
Power Management Capability, Version 1.0
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
IRQ Summary: IRQs 5,10,11,14,15 are used by PCI devices
Shared IRQs: IRQ 11 is shared by 3 PCI Devices
NT: Close driver : Operation was successful
NT: Open SCM : Operation was successful
NT: Stop driver : Operation was successful
NT: Remove driver : Operation was successful
NT: Close SCM : Operation was successful