مودم من رو خود Jaunty می شناسه. اما خب نمی تونم با gnome-ppp یا wvdial یا حتی kppp به اینترنت متصل شم. برای wvdial می نویسه:
که البته دستی ترمینیتش کردم.کد:sudo wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: AT S11=50
AT S11=50
OK
--> Modem initialized.
--> Sending: ATDT9712206
--> Waiting for carrier.
ATDT9712206
CONNECT 46667
Cisco 12000
K.Montazeri Router Administrator
User Access Verification
Username:
--> Carrier detected. Waiting for prompt.
--> Connected, but carrier signal lost! Retrying...
--> Sending: ATDT9712206
--> Waiting for carrier.
Username:
Username:
NO CARRIER
--> No Carrier! Trying again.
--> Sending: ATDT9712206
--> Waiting for carrier.
ATDT9712206
NO CARRIER
--> No Carrier! Trying again.
--> Sending: ATDT9712206
--> Waiting for carrier.
ATDT9712206
^CCaught signal 2: Attempting to exit gracefully...
--> Disconnecting at Fri Jul 17 16:31:57 2009
برای gnome-ppp هم دارم:
اضافه کنم که شماره گیری رو با یه کالر آی دی چک کردم و درست انجام می شه.کد:--> Ignoring malformed input line: ";Do NOT edit this file by hand!"
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATM1L3DT9712206
--> Waiting for carrier.
ATM1L3DT9712206
NO CARRIER
--> No Carrier! Trying again.
--> Maximum Attempts Exceeded..Aborting!!
--> Disconnecting at Fri Jul 17 16:27:50 2009
کد های زیر هم شاید مفید باشن:
و این هم wvdial.confکد:sudo wvdialconf /etc/wvdial.conf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1 S2 S3
WvModem<*1>: Cannot get information for serial port.
ttySL0<*1>: ATQ0 V1 E1 -- OK
ttySL0<*1>: ATQ0 V1 E1 Z -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem
ttySL0<*1>: Speed 4800: AT -- OK
ttySL0<*1>: Speed 9600: AT -- OK
ttySL0<*1>: Speed 19200: AT -- OK
ttySL0<*1>: Speed 38400: AT -- OK
ttySL0<*1>: Speed 57600: AT -- OK
ttySL0<*1>: Speed 115200: AT -- OK
ttySL0<*1>: Speed 230400: AT -- OK
ttySL0<*1>: Speed 460800: AT -- OK
ttySL0<*1>: Max speed is 460800; that should be safe.
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
Found a modem on /dev/ttySL0.
Modem configuration written to /etc/wvdial.conf.
ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
که البته با باود 115200 هم چک کردم و همین مشکل بود.کد:[Dialer Defaults]
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Phone = 9712206
ISDN = 0
Username = username
Init1 = ATZ
Password = pass
Modem = /dev/ttySL0
Baud = 460800
kppp هم همین مشکل رو داره و البته pppconfig رو هم انجام دادم. و با pon و البته pppd call هم نتونستم وصل شم که اون ها هیچ خروجی به من نمی دادن تا بفهمم دلیل چیه.
از دوستان کسی می تونه به من کمک کنه؟
