سلام
نه دوست من چیپست مودم شما کانکسانت نیست
دیگه وقت خودتون رو با درایور های کانکسانت هدر ندید
چیپش via هست
و همونطور که شما متوجه شدید به درد کار با لینوکس نمی خوره
من کلی جستجو کردم ولی چیزی پیدا نشد
Printable View
سلام
نه دوست من چیپست مودم شما کانکسانت نیست
دیگه وقت خودتون رو با درایور های کانکسانت هدر ندید
چیپش via هست
و همونطور که شما متوجه شدید به درد کار با لینوکس نمی خوره
من کلی جستجو کردم ولی چیزی پیدا نشد
پيشنهاد من:
1. در صورتيكه ميخواين كمي خرج كنين يه مودم us robotics اكسترنال
2. مودم زي سايبر كه با درايورهاي مورد نياز براي لينوكس ارايه ميشه
خیلی ممنون از راهنمایی های دوستان
rootnt عزیز ممکنه بجز مودمی که جناب raeesi معرفی کردن یه چندتا مودم اینترنال که نصبشون در لینوکس مشکلی نداره معرفی کنید؟
روی مودم ها مشخص میکنه که چیپستش از نوع کانکسانت هست؟ که برم مودمی بگیرم که از این نوع باشه؟
raeesi عزیزنقل قول:
نوشته شده توسط raeesi
پيشنهاد من:
1. در صورتيكه ميخواين كمي خرج كنين يه مودم us robotics اكسترنال
2. مودم زي سايبر كه با درايورهاي مورد نياز براي لينوكس ارايه ميشه
این مودم زی سایبر که میگید اینترنال هست؟ همه مدل هاش درایور لینوکس دارند؟ اگه نه چه مدل هایی دارن؟
فقط امیدوارم این مودم هایی که معرفی میکنید بتونم گیر بیارم ( تهران نیستم) وگرنه حالا حالا ها علاف میشم!
مودمهای gigabyte و zoltrix که همه جا هم پیدا می شه چیپستشون کانکسانته خیلی هم ارزونه
خیلی ممنون دوست عزیز
شرمنده که انقدر سوال پرسیدم!
سلام
لطف کنید بگین چیپست مودم من چیه و ایا درایورش در دسترس هست؟
تشکر از لطفتون.
Craig Hart's PCI+AGP bus sniffer, Version 1.4, freeware made in 1996-2005.
Searching for Devices using CFG Mechanism 1 [OS: Win XP Service Pack 2]
Bus 0 (PCI), Device Number 0, Device Function 0
Vendor 1106h VIA Technologies Inc
Device 0258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 2230h (Has Capabilities List, Supports 66MHz, Received Master Abort, Medium Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 08h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Subsystem ID 02581106h Unknown (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 0 is a Memory Address (anywhere in 0-4Gb, Prefetchable) : F8000000h
New Capabilities List Present:
AGP Capability, Version 3.5 (AGP 8x and 4x, appendix register support)
AGP Speed(s) Supported : 1x 2x 4x
FW Transfers Supported : Yes
>4Gb Address Space Supported : No
Sideband Addressing Supported : Yes
AGP v3.0 Operation Mode Available : No
Maximum Command Queue Length : 32 bytes
AGP Speed Selected : 4x
FW Transfers Enabled : No
>4Gb Address Space Enabled : No
AGP Enabled : Yes
Sideband Addressing Enabled : Yes
Current Command Queue Length : 1 byte
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Bus 0 (PCI), Device Number 0, Device Function 1
Vendor 1106h VIA Technologies Inc
Device 1258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 0200h (Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Bus 0 (PCI), Device Number 0, Device Function 2
Vendor 1106h VIA Technologies Inc
Device 2258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 0200h (Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Bus 0 (PCI), Device Number 0, Device Function 3
Vendor 1106h VIA Technologies Inc
Device 3258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 0200h (Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Bus 0 (PCI), Device Number 0, Device Function 4
Vendor 1106h VIA Technologies Inc
Device 4258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 0200h (Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Bus 0 (PCI), Device Number 0, Device Function 7
Vendor 1106h VIA Technologies Inc
Device 7258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 0200h (Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Bus 0 (PCI), Device Number 1, Device Function 0
Vendor 1106h VIA Technologies Inc
Device B198h ProSavageDDR P4X600,Apollo KT400/A/600 CPU to AGP Bridge
Command 0107h (I/O Access, Memory Access, BusMaster, System Errors)
Status 0230h (Has Capabilities List, Supports 66MHz, Medium Timing)
Revision 00h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus Number 1
Secondary Bus Command 000Fh (parity detection, ISA mapping, VGA mapping)
Secondary Bus Status 2220h (Supports 66MHz, Received Master Abort, Medium Timing)
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : C000h to CFFFh (16-bit)
Memory Range Passed to Secondary Bus : FFD00000h to FFDFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : E7F00000h to F7EFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Bus 0 (PCI), Device Number 12, Device Function 0
Vendor 1057h Motorola
Device 3052h Unknown
Command 0090h (Bus Access Disabled!!, MemWrite+Invalidate, Wait Cycles)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 04h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 01h, Maximum Bus Latency 3Eh
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Simple Communication, type Hayes Compatible Modem
Subsystem ID 30201057h Unknown
Subsystem Vendor 1057h Motorola
Address 0 is a Memory Address (anywhere in 0-4Gb) : FFCFE000h
Address 1 is an I/O Port : 0000EC00h
System IRQ 16, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D3hot (Device off: no power to device, maximum power saving)
Bus 0 (PCI), Device Number 15, Device Function 0
Vendor 1106h VIA Technologies Inc
Device 0571h VT82xxxx EIDE Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 06h, Header Type 00h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID 05711106h VT82Cxxxx EIDE Controller (All VIA Chipsets) (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000FC00h
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Bus 0 (PCI), Device Number 16, Device Function 0
Vendor 1106h VIA Technologies Inc
Device 3038h VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 81h, Header Type 80h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30381106h Unknown (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000DC00h
System IRQ 21, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Bus 0 (PCI), Device Number 16, Device Function 1
Vendor 1106h VIA Technologies Inc
Device 3038h VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 81h, Header Type 80h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30381106h Unknown (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000E000h
System IRQ 21, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Bus 0 (PCI), Device Number 16, Device Function 2
Vendor 1106h VIA Technologies Inc
Device 3038h VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 81h, Header Type 80h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30381106h Unknown (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000E400h
System IRQ 21, INT# B
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Bus 0 (PCI), Device Number 16, Device Function 3
Vendor 1106h VIA Technologies Inc
Device 3038h VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 81h, Header Type 80h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30381106h Unknown (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000E800h
System IRQ 21, INT# B
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Bus 0 (PCI), Device Number 16, Device Function 4
Vendor 1106h VIA Technologies Inc
Device 3104h VT6202/12 USB 2.0 Enhanced Host Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 86h, Header Type 80h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB 2.0 (EHCI)
Subsystem ID 31041106h VT6202 USB 2.0 Enhanced Host Controller (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 0 is a Memory Address (anywhere in 0-4Gb) : FFCFFE00h
System IRQ 21, INT# C
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Bus 0 (PCI), Device Number 17, Device Function 0
Vendor 1106h VIA Technologies Inc
Device 3227h VT8237 PCI to ISA Bridge
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID 00001106h Unknown
Subsystem Vendor 1106h VIA Technologies Inc
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Bus 0 (PCI), Device Number 17, Device Function 5
Vendor 1106h VIA Technologies Inc
Device 3059h VT8233/A AC'97 Enhanced Audio Controller
Command 0001h (I/O Access)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 60h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 04301462h Onboard AC'97 Enhanced Audio Controller (Guess Only!)
Subsystem Vendor 1462h Micro-Star International Co Ltd (MSI)
Address 0 is an I/O Port : 0000D800h
System IRQ 22, INT# C
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Bus 0 (PCI), Device Number 18, Device Function 0
Vendor 1106h VIA Technologies Inc
Device 3065h VT6102 Rhine II Fast Ethernet Adapter
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 78h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 03h, Maximum Bus Latency 08h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Network, type Ethernet
Subsystem ID 043C1462h Unknown
Subsystem Vendor 1462h Micro-Star International Co Ltd (MSI)
Address 0 is an I/O Port : 0000D400h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFCFFF00h
System IRQ 23, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Bus 1 (AGP), Device Number 0, Device Function 0
Vendor 1002h ATI Technologies Inc
Device 5159h Radeon 7000 Series (RV100)
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 02B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back Trans., Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer FFh
Minimum Bus Grant 08h, Maximum Bus Latency 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 40021458h Radeon 7000 PRO MAYA AV Series
Subsystem Vendor 1458h Giga-Byte Technology
Address 0 is a Memory Address (anywhere in 0-4Gb, Prefetchable) : E8000000h
Address 1 is an I/O Port : 0000C800h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFDF0000h
System IRQ 16, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
AGP Capability, Version 2.0 (AGP 4x and below support)
AGP Speed(s) Supported : 1x 2x 4x
FW Transfers Supported : No
>4Gb Address Space Supported : No
Sideband Addressing Supported : Yes
Maximum Command Queue Length : 48 bytes
AGP Speed Selected : 4x
FW Transfers Enabled : No
>4Gb Address Space Enabled : No
AGP Enabled : Yes
Sideband Addressing Enabled : Yes
Current Command Queue Length : 32 bytes
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
IRQ Summary: IRQs 14,15,16,21,22,23 are used by PCI devices
Shared IRQs: IRQ 16 is shared by 2 PCI Devices
IRQ 21 is shared by 5 PCI Devices
IRQ control is currently managed by the system APIC controller - IRQ info is
...
اگه میشه لطف کنین بگین چیپ مودم من چیه و ایا درایورش در دسترس هست؟
با تشکر
Craig Hart's PCI+AGP bus sniffer, Version 1.4, freeware made in 1996-2005.
Searching for Devices using CFG Mechanism 1 [OS: Win XP Service Pack 2]
Bus 0 (PCI), Device Number 0, Device Function 0
Vendor 1106h VIA Technologies Inc
Device 0258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 2230h (Has Capabilities List, Supports 66MHz, Received Master Abort, Medium Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 08h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Subsystem ID 02581106h Unknown (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 0 is a Memory Address (anywhere in 0-4Gb, Prefetchable) : F8000000h
New Capabilities List Present:
AGP Capability, Version 3.5 (AGP 8x and 4x, appendix register support)
AGP Speed(s) Supported : 1x 2x 4x
FW Transfers Supported : Yes
>4Gb Address Space Supported : No
Sideband Addressing Supported : Yes
AGP v3.0 Operation Mode Available : No
Maximum Command Queue Length : 32 bytes
AGP Speed Selected : 4x
FW Transfers Enabled : No
>4Gb Address Space Enabled : No
AGP Enabled : Yes
Sideband Addressing Enabled : Yes
Current Command Queue Length : 1 byte
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Bus 0 (PCI), Device Number 0, Device Function 1
Vendor 1106h VIA Technologies Inc
Device 1258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 0200h (Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Bus 0 (PCI), Device Number 0, Device Function 2
Vendor 1106h VIA Technologies Inc
Device 2258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 0200h (Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Bus 0 (PCI), Device Number 0, Device Function 3
Vendor 1106h VIA Technologies Inc
Device 3258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 0200h (Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Bus 0 (PCI), Device Number 0, Device Function 4
Vendor 1106h VIA Technologies Inc
Device 4258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 0200h (Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Bus 0 (PCI), Device Number 0, Device Function 7
Vendor 1106h VIA Technologies Inc
Device 7258h PT880 CPU to PCI Bridge
Command 0006h (Memory Access, BusMaster)
Status 0200h (Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
Bus 0 (PCI), Device Number 1, Device Function 0
Vendor 1106h VIA Technologies Inc
Device B198h ProSavageDDR P4X600,Apollo KT400/A/600 CPU to AGP Bridge
Command 0107h (I/O Access, Memory Access, BusMaster, System Errors)
Status 0230h (Has Capabilities List, Supports 66MHz, Medium Timing)
Revision 00h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus Number 1
Secondary Bus Command 000Fh (parity detection, ISA mapping, VGA mapping)
Secondary Bus Status 2220h (Supports 66MHz, Received Master Abort, Medium Timing)
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : C000h to CFFFh (16-bit)
Memory Range Passed to Secondary Bus : FFD00000h to FFDFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : E7F00000h to F7EFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Bus 0 (PCI), Device Number 12, Device Function 0
Vendor 1057h Motorola
Device 3052h Unknown
Command 0090h (Bus Access Disabled!!, MemWrite+Invalidate, Wait Cycles)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 04h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 01h, Maximum Bus Latency 3Eh
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Simple Communication, type Hayes Compatible Modem
Subsystem ID 30201057h Unknown
Subsystem Vendor 1057h Motorola
Address 0 is a Memory Address (anywhere in 0-4Gb) : FFCFE000h
Address 1 is an I/O Port : 0000EC00h
System IRQ 16, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D3hot (Device off: no power to device, maximum power saving)
Bus 0 (PCI), Device Number 15, Device Function 0
Vendor 1106h VIA Technologies Inc
Device 0571h VT82xxxx EIDE Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 06h, Header Type 00h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID 05711106h VT82Cxxxx EIDE Controller (All VIA Chipsets) (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000FC00h
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Bus 0 (PCI), Device Number 16, Device Function 0
Vendor 1106h VIA Technologies Inc
Device 3038h VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 81h, Header Type 80h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30381106h Unknown (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000DC00h
System IRQ 21, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Bus 0 (PCI), Device Number 16, Device Function 1
Vendor 1106h VIA Technologies Inc
Device 3038h VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 81h, Header Type 80h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30381106h Unknown (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000E000h
System IRQ 21, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Bus 0 (PCI), Device Number 16, Device Function 2
Vendor 1106h VIA Technologies Inc
Device 3038h VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 81h, Header Type 80h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30381106h Unknown (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000E400h
System IRQ 21, INT# B
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Bus 0 (PCI), Device Number 16, Device Function 3
Vendor 1106h VIA Technologies Inc
Device 3038h VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 81h, Header Type 80h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30381106h Unknown (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 4 is an I/O Port : 0000E800h
System IRQ 21, INT# B
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Bus 0 (PCI), Device Number 16, Device Function 4
Vendor 1106h VIA Technologies Inc
Device 3104h VT6202/12 USB 2.0 Enhanced Host Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 86h, Header Type 80h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Serial, type USB 2.0 (EHCI)
Subsystem ID 31041106h VT6202 USB 2.0 Enhanced Host Controller (Generic ID)
Subsystem Vendor 1106h VIA Technologies Inc
Address 0 is a Memory Address (anywhere in 0-4Gb) : FFCFFE00h
System IRQ 21, INT# C
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
Bus 0 (PCI), Device Number 17, Device Function 0
Vendor 1106h VIA Technologies Inc
Device 3227h VT8237 PCI to ISA Bridge
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID 00001106h Unknown
Subsystem Vendor 1106h VIA Technologies Inc
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Bus 0 (PCI), Device Number 17, Device Function 5
Vendor 1106h VIA Technologies Inc
Device 3059h VT8233/A AC'97 Enhanced Audio Controller
Command 0001h (I/O Access)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 60h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 04301462h Onboard AC'97 Enhanced Audio Controller (Guess Only!)
Subsystem Vendor 1462h Micro-Star International Co Ltd (MSI)
Address 0 is an I/O Port : 0000D800h
System IRQ 22, INT# C
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Bus 0 (PCI), Device Number 18, Device Function 0
Vendor 1106h VIA Technologies Inc
Device 3065h VT6102 Rhine II Fast Ethernet Adapter
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 78h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 03h, Maximum Bus Latency 08h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Network, type Ethernet
Subsystem ID 043C1462h Unknown
Subsystem Vendor 1462h Micro-Star International Co Ltd (MSI)
Address 0 is an I/O Port : 0000D400h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFCFFF00h
System IRQ 23, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Bus 1 (AGP), Device Number 0, Device Function 0
Vendor 1002h ATI Technologies Inc
Device 5159h Radeon 7000 Series (RV100)
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 02B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back Trans., Medium Timing)
Revision 00h, Header Type 00h, Bus Latency Timer FFh
Minimum Bus Grant 08h, Maximum Bus Latency 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 40021458h Radeon 7000 PRO MAYA AV Series
Subsystem Vendor 1458h Giga-Byte Technology
Address 0 is a Memory Address (anywhere in 0-4Gb, Prefetchable) : E8000000h
Address 1 is an I/O Port : 0000C800h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFDF0000h
System IRQ 16, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
AGP Capability, Version 2.0 (AGP 4x and below support)
AGP Speed(s) Supported : 1x 2x 4x
FW Transfers Supported : No
>4Gb Address Space Supported : No
Sideband Addressing Supported : Yes
Maximum Command Queue Length : 48 bytes
AGP Speed Selected : 4x
FW Transfers Enabled : No
>4Gb Address Space Enabled : No
AGP Enabled : Yes
Sideband Addressing Enabled : Yes
Current Command Queue Length : 32 bytes
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
IRQ Summary: IRQs 14,15,16,21,22,23 are used by PCI devices
Shared IRQs: IRQ 16 is shared by 2 PCI Devices
IRQ 21 is shared by 5 PCI Devices
IRQ control is currently managed by the system APIC controller - IRQ info is
not actual hardware settings...
سلام به همه!
این مشخصات من هست:
Modem:
Zling HCF
Linux:
linux-eg41 2.6.18.2-.34-defult #1 smp mon nov 27 11:46 : 27 UTC 2006 i686 i686 i386 GNU/Linux
از Uname -a گرفتم.
Linux modem Driver:
Instructions:کد:http://www.z-cyber.net/Zling_HCF.htm#linux
Instructions کمکی نکردو لطفا یک نگاهی بفرمایید.کد:http://www.zoltrix.com/PUBLIC2/MODEM/SmartSpirit/readme2.txt
اینم ریزالت PCI 32.
Vendor 14F1h Conexant Systems
Device 1056h HCF 56k Data/Fax/Voice/Spkp Modem (Worldwide)
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
g)
Revision 08h, Header Type 00h, Bus Latency Timer 20h
Self test 00h (Self test not supported)
PCI Class Simple Communication, type Other
Subsystem ID 105614F1h Unknown (Generic ID)
Subsystem Vendor 14F1h Conexant Systems
Address 0 is a Memory Address (anywhere in 0-4Gb) : F9100000h
Address 1 is an I/O Port : 0000D000h
System IRQ 19, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
لطفا برای کسی توضیح بدید که کلا 2 ساعت توی لینوکس بوده!
از چه توزيعي استفاده ميكنيد؟
آيا فايل modem_load و modem_install رو اديت كردين؟ (اگه از توزيعي بجز Suse يا Redhat استفاده ميكنيد).
ای وای! یادم رفت بگم!نقل قول:
Suse 10.2
استفاده میکنم.
هم با ادیت، هم بی ادیت! طبق Instructions عمل کردم. نشد!
با سلام . من چون از ADSL استفاده می کنم هیچ وقت نرفتم دنبال نصب مودم کامپیوترم که در لینوکس مشکل داره . ولی دیشب به سرم زد که درستش کنم و بعد از چند ساعت کلنجار رفتن تونستم مودم رو از طریق سایت
نصب کنم. توی این سایت دو نوع درایور وجود داره. یکی نسخه مجانی که سرعت مودم حداکثر۱۴.۴ خواهد بود و یکی هم نسخه پولی که سرعت ۵۶ خواهد بود. که من نسخه مجانی رو نصب کردم . حالا می خواستم بپرسم که آیا راهی نیست که از حداکثر سرعت مودم استفاده کرد؟کد:http://www.linuxant.com/drivers/
در ضمن دوستانی که در نصب مودم مشکل دارند این فایل رو ( که تازه آپدیت شده ) دانلود کنندو از حالت فشرده خارج کنند و فایل درون اون رو از طریق terminal یا konsole با دستور زیر اجرا کنند و نتیجش رو اینجا بذارند. شاید بتونیم کمک کنم.
کد:http://linmodems.technion.ac.il/packages/scanModem.gz
کد:cd to directory
sh scanModem
حسين عزيز توي راهنماي تصب مودم توي همين سايت و irtux و لينوكسيران و ... اين نكته هم ذكر شده كه شما ميتوني با استفاده از key generator يك key براي سيستم خودتون generate كنين و برنامه رو از حالت trial به full تغيير بدين!البته راه بهتري هم هست و اونم اينكه مبلغي كه توي سايت درج شده به مديران Linuxant پرداخت كنين :)
پ.ن: البته امروزه درايور مودمهاي زيادي از طريق وب سايت شركت سازنده و يا وب سايتهاي ديگر قابل دريافته و نيازي به امر ناپسندانه كركينگ احساس نميشه!!!
براي نصب از فايل مخصوص Suse استفاده كردين؟نقل قول:
پ.ن (من خواستم پارسيكس آزمايش كنم . نصب كردم ولي هركاري ميكنم مودمم توش نصب نميشه!!) هم با درايور خود ري سايبر و هم با درايور لينوكسانت :( سيستم detect ميكنه ولي كار نميكنه :(
بله! امتحان کردم! خبری نیست که نیست! دارم میرم Adsl بگیرم! اگر هزار تا مشکله دیگه هم پیش بیاد، من که لینوکسو بیخیال نمیشم!
raeesi
دوست عزیز میشه لینک دانلود این Key.Gen رو قرار بدی؟ من فدورا 5 روی هارد دومم نصب کردم و میخوام امتحان کنم. اگر ممکنه یه لطفی کن و لینکو قرار بده.
با تشکر از حسین عزیز بابت قرار دادن اطلاعات. (تعداد صفحات زیاده و واقعا شخصی مثل من که هیچی از لینوکس نمیفهمه گیج میشه. اما خوش شانس بودم و تو صفحه آخر مطلب مختصر و خوبی پیدا کردم!)
توی پارسیکس احتیاج نیست که درایورهای لینوکسانت رو نصب کنیدنقل قول:
به صورت پیش فرض روی سیستم قرار داره
فقط کافیه شما hsfconfig یا hcfpciconfig رو بزنید و بقیه کار
دوست عزيز شما با استفاده از اين لينك ميتوني keygen براي درايورهاي لينوكسانت دانلود و استفاده كني:نقل قول:
کد:http://irphoto.persiangig.com/other/hcfkeygen-1.02.tar.gz
:18: براي من مودم detect ميشه ولي كار نميكنه و علكي ارور ميده كه لاين اشغاله!!!!نقل قول:
من از درايور كانكسانت استفاده كردم در قسمت كانفيگ وقتي /usr/sbin/hcfpciconfig رو مي زنم يكم كار مي كنه ميگه hcfpcihw َAlready in use من نمي دونم اين چيه كه هميشه اجراست و اين ماژول مذكور كجاست و كلا راهنمايي مي خوام يه چيز ديگه من UDEV ام كار نمي كنه آيا به اون مربوطه.
کد:http://wiki.ubuntu.ir/DialupModemHowto
سلام من این داریور را برای مودم خودم دانلود کردم Smart Sprit حالا چه جور این را باید به یک بسته RPM تبدیل کنم؟
خوب فایل rpm رو دانلود می کردی . از یکی از این دوسایت با توجه به مدل مودمت ( hcf یا hsf ) و با توجه به نوع توزیع و ورژن کرنلت فایل مورد نظر را دانلود کن.نقل قول:
کد:http://www.linuxant.com/drivers/hcf/full/downloads.php
کد:http://www.linuxant.com/drivers/hsf/full/downloads.php
سلام
لطف کنید بگین چیپست مودم من چیه و ایا درایورش در دسترس هست؟
تشکر از لطفتون.
Vendor 8086h Intel Corporation
Device 27D2h Unknown
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 01h, Header Type 81h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 64 Bytes (16 DWords)
PCI Class Bridge, type PCI to PCI
System IRQ 17, INT# B
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 16, Subordinate Bus Number 16
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 2000h (Received Master Abort, Fast Timing)
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : F4000000h to F40FFFFFh
Prefectchable Memory Range Passed to Secondary Bus : None
New Capabilities List Present:
PCI Express Capability, Version 1
Device/Port Type : Root port of PCI Express Root Complex
Port is an Expansion Slot
Unsupported Request Severity is Non-Fatal
AUX Power Detected
Maximum Link speed : 2.5Gb/s
Maximum Link Width : x1
Link Port Number : 2
Common Clock Configuration In Use
Current Link speed : 2.5Gb/s
Current Link Width : x1
Hot Plug Surprise is Possible
Hot Plug Capable
Physical slot Number 0
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 32-bit addresses
Subsystem ID & Subsystem Vendor ID Capability
SSVID : 103Ch
SSID : 30A2h
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Vendor 8086h Intel Corporation
Device 27D6h Unknown
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 01h, Header Type 81h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 64 Bytes (16 DWords)
PCI Class Bridge, type PCI to PCI
System IRQ 19, INT# D
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 32, Subordinate Bus Number 32
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 2000h (Received Master Abort, Fast Timing)
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 2000h to 3FFFh (16-bit)
Memory Range Passed to Secondary Bus : F0000000h to F3FFFFFFh
Prefectchable Memory Range Passed to Secondary Bus : None
New Capabilities List Present:
PCI Express Capability, Version 1
Device/Port Type : Root port of PCI Express Root Complex
Port is an Expansion Slot
Unsupported Request Severity is Non-Fatal
AUX Power Detected
Maximum Link speed : 2.5Gb/s
Maximum Link Width : x1
Link Port Number : 4
Asynchronous Clocking in Use
Current Link speed : 2.5Gb/s
Current Link Width : x0
Hot Plug Surprise is Possible
Hot Plug Capable
Physical slot Number 0
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 32-bit addresses
Subsystem ID & Subsystem Vendor ID Capability
SSVID : 103Ch
SSID : 30A2h
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Vendor 8086h Intel Corporation
Device 27C8h Unknown
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 4 is an I/O Port : 00004020h
System IRQ 20, INT# A
Vendor 8086h Intel Corporation
Device 27C9h Unknown
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 4 is an I/O Port : 00004040h
System IRQ 17, INT# B
Vendor 8086h Intel Corporation
Device 27CAh Unknown
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 4 is an I/O Port : 00004060h
System IRQ 18, INT# C
Vendor 8086h Intel Corporation
Device 27CBh Unknown
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 4 is an I/O Port : 00004080h
System IRQ 19, INT# D
Vendor 8086h Intel Corporation
Device 27CCh Unknown
Command 0006h (Memory Access, BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timin
g)
Revision 01h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Serial, type USB 2.0 (EHCI)
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 0 is a Memory Address (anywhere in 0-4Gb) : F4584000h
System IRQ 20, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 375mA
USB 2.0 EHCI Debug Port Capability
Vendor 8086h Intel Corporation
Device 2448h 82801BAM/CAM/DBM (ICH2-M/3-M/4-M) Hub Interface to PCI Bridge
Command 0107h (I/O Access, Memory Access, BusMaster, System Errors)
Status 0010h (Has Capabilities List, Fast Timing)
Revision E1h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI (Subtractive Decode)
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 2, Subordinate Bus Number 3
Secondary Bus Command 0006h (ISA mapping)
Secondary Bus Status 2280h (Supports Back-To-Back Trans., Received Master Abo
rt, Medium Timing)
Secondary Bus Latency 20h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : F4100000h to F43FFFFFh
Prefectchable Memory Range Passed to Secondary Bus : None
New Capabilities List Present:
Subsystem ID & Subsystem Vendor ID Capability
SSVID : 103Ch
SSID : 30A2h
Vendor 8086h Intel Corporation
Device 27B9h Unknown
Command 0107h (I/O Access, Memory Access, BusMaster, System Errors)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 01h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
New Capabilities List Present:
Vendor-Dependant Capability
Vendor 8086h Intel Corporation
Device 27C4h Unknown
Command 0005h (I/O Access, BusMaster)
Status 02B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back Tran
s., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 0 is an I/O Port : 00000000h
Address 1 is an I/O Port : 00000000h
Address 2 is an I/O Port : 00000000h
Address 3 is an I/O Port : 00000000h
Address 4 is an I/O Port : 000040A0h
System IRQ 11, INT# B
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D3hot
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
Vendor 104Ch Texas Instruments (TI)
Device 8039h Unknown
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 00h, Header Type 82h, Bus Latency Timer 40h
Self test 00h (Self test not supported)
Cache line size 64 Bytes (16 DWords)
PCI Class Bridge, type PCI to Cardbus
System IRQ 18, INT# A
PCI bus number 2, CardBus bus number 3, Subordinate bus number 3
CardBus latency 00h
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
Vendor 104Ch Texas Instruments (TI)
Device 803Ah Unknown
Command 0006h (Memory Access, BusMaster)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 40h
Minimum Bus Grant 02h, Maximum Bus Latency 04h
Self test 00h (Self test not supported)
Cache line size 64 Bytes (16 DWords)
PCI Class Serial, type OHCI FireWire
Subsystem ID 30A2103Ch Unknown
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 0 is a Memory Address (anywhere in 0-4Gb) : F4101000h
Address 1 is a Memory Address (anywhere in 0-4Gb) : F4104000h
System IRQ 19, INT# B
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
Vendor 14E4h Broadcom Corp
Device 170Ch BCM440x 100Base-TX Fast Ethernet
Command 0000h (Bus Access Disabled!!)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 02h, Header Type 00h, Bus Latency Timer 40h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 30A2103Ch BCM440x 10/100 Integrated Controller (Guess Only!)
Subsystem Vendor 103Ch Hewlett-Packard Company
Address 0 is a Memory Address (anywhere in 0-4Gb) : F4108000h
System IRQ 10, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D3hot (Device off: no power to device, maximum power
saving)
IRQ Summary: IRQs 10,11,14,15,16,17,18,19,20 are used by PCI devices
Shared IRQs: IRQ 16 is shared by 3 PCI Devices
IRQ 17 is shared by 2 PCI Devices
IRQ 18 is shared by 2 PCI Devices
IRQ 19 is shared by 3 PCI Devices
IRQ 20 is shared by 2 PCI Devices
IRQ control is currently managed by the system APIC controller - IRQ info is
not actual hardware settings...
NT: Close driver : Operation was successful
NT: Open SCM : Operation was successful
NT: Stop driver : Operation was successful
NT: Remove driver : Operation was successful
NT: Close SCM : Operation was successful
من مي خواهم با مودم Siemens به اينترنت ADSL وصل شم
ولي زياد با لينوكس آشنايي ندارم اگه ميشه راهنمايي يا
آموزش نصب مودم و راه اندازيشو بگيد خيلي ممنون
سلامنقل قول:
اگر مودم شما پورت lan داره کافیه که IP رو تنظیم کنید بهتره که نوع توزیع مورداستفاده هم بگید تا بهتر بشه کمک کرد
با سلام.نقل قول:
اگه ميشه اسم و مدل مدمو بزارين چون منم مي خوام مودم بگيرم ولي نمي دونم چه مودمي براي ADSL تو لينوكس خوبه.
بعد هم مراحل كامل شناسي مودم USB و تنظيم IP در لينوكس رو بزارين.:10:
نقل قول:
بله پورت lan و usb داره
"نوع توزیع مورداستفاده" يعني چي؟
به هر نسخه از لینوکس یک توزیع گفته میشه. یعنی اسم لینوکستون چیه ؟ فدورا , سوسه ,اوبونتو و ...نقل قول:
نقل قول:
كارامد (فارسي) ولي فكر كنم از گنو تبديل شده باشه
البته کاآمد از نسخه ی Slax که خود بر پایه ی Slackware درست شده، و در واقع صرفا فارسی شده.نقل قول:
البته می دوونم جاش نیست ولی می خواستم ببینم دوستمون که از این توزیع استفاده می کنه راضی هست و چرا این توزیع رو انتخاب کرده؟:20:
من چون ويندوز هم دارم بيشتر از
ويندوز استفاده مي كنم و تازه مي خواهم
با هاش كار كنم ولي فكر نكنم نسخه خوبي
باشه تا حالا چند دفعه گير كردم نتونستم
كاري بكنم البته شايدم براي ناشي بودن بنده باشه
آقا هر کاری کردم مودکمم نصب نشد که نشد:41:
چیپش hsf هستش.راه حل هایی رو که تو این چند صفحه آخر هم گفتید انجام دادم ولی باز نمیشناسه.
با wvdial که میگه مودم detect نمیشه.با pppk هم کانکشن که میسازم و کانکت میشم میزنه modem busy.
خستم کرده.
البته مودمم smart link هستش راهنمای فارسی که تو سایت ابونتو بود رو هم خوندم و انجام دادم اونم نشد.
داخل سی دی مودم درایور لینوکس موجود هستش فقط دستوراتی که برای نصب تو ترمینال نوشته رو اجرا نمیکنه.
این راهنمای نصب خود شرکت سازنده:
نقل قول:
Smart Link Ltd.
Sep 30, 2003کد:http://www.smlink.com
Smart Link Soft Modem for Linux
-------------------------------
Introduction
============
This is Smart Link Soft Modem for Linux version 2.9. It provides
full-featured 56K Voice Fax Modem.
This is implemented as generic application (slmodemd) and set of
hardware specific kernel-space drivers (slamr, slusb).
ALSA modem drivers may be used instead of proprietary ones (see ALSA mode).
Features
========
Modem: V.92, V.90, V.34, V.32bis, V.32, V.23, V.22, V.21, Bell 103/212.
Flow control: V.42.
Compression: V.44, V.42bis.
Fax: Class 1.
Voice: V253 like modem.
Multiple modems are supported.
Supported Hardware
==================
HAMR5600 based AMR/CNR/MDC/ACR modem cards on the following Southbridge
chips:
- Intel ICH0,ICH2, ICH3, ICH4
- Via 686A, 686B, 8231, 8233
- SiS 630
- ALI 1535.
SmartPCI56/561/562/563 based PCI modem cards.
SmartUSB56 based USB modem.
Requirements
============
CPU: Intel Pentium II, Celron. AMD K6, Cyrix 500MHz or higher.
Memory: 64MB.
OS: Linux 2.4. You need the kernel header files at least (or full kernel
source tree) installed and configured.
Linux 2.6. You need the full kernel source tree installed and configured.
Note: Most Linux Distributions have 'ready to use' kernel source package -
be sure that this is installed.
Installation
============
1. Unpack tar.gz package file:
$ gzip -dc slmodem-2.9.X.tar.gz | tar xf -
2. 'cd' to package directory:
$ cd slmodem-2.9.X
3. Review and edit 'Makefile' (if need):
In many cases you will need to correct path to your local kernel
source tree:
KERNEL_DIR=/path/to/linux
Default KERNEL_DIR is '/lib/modules/<kerne-version>/build'. Many Linux
Distributions use directory '/usr/src/linux-<version>' also.
Note: If you are using Linux kernel 2.4, only header files should be
available for build in $(KERNEL_DIR)/include
Another way to pass right value KERNEL_DIR is to use command line
parameter while running 'make':
$ make KERNEL_DIR=/path/to/linux ...
4. Run 'make' command to compile package:
$ make
5. Install. As 'root' user run:
# make install
It will install:
- application 'slmodemd' under '/usr/sbin' directory
- hardware specific drivers (kernel modules) 'slamr' and 'slusb'
under conventional kernel modules directory
- character device nodes '/dev/slamr0-3' with major number 212
(for pci modems) and '/dev/slusb0-3' with major number 213
(for usb modems).
- config modules for autoloading (by editing file '/etc/modules.conf')
(only with 2.4 kernels)
6. Config modem country.
Use AT+GCI=<T.35 country code> command to setup country.
Also you can setup default modem country by passing command line
parameter '--country=MY_COUNTRY' to program 'slmodemd'.
See output of 'slmodemd --countrylist' for a list of supported
country names and T.35 country codes (see also 'slmodemd --help').
Note: Command ATI7 shows currently installed country setting.
8. Uninstallation.
In package directory just type:
# make uninstall
Getting Started
===============
After successful installation and configuration:
1. Load modem driver.
Load your modem hardware specific kernel module:
# modprobe slamr
if you are using AMR/CNR/PCI modem, or
# modprobe slusb
if you are using SmartUSB56 Modem.
Note: this will be done automatically when modules were
configured for 'loading on demand'
Note: this is safe to load both 'alamr' and 'slusb' modules.
2. Run soft modem application.
# /usr/sbin/slmodemd [options] <device_name>
Where device name is appropriate device node for your modem
(look at output of 'dmesg' command).
Run '/usr/sbin/slmodemd --help' for details.
Examples:
# /usr/sbin/slmodemd --country=USA /dev/slamr0
, or for SmartUSB56 Modems:
# /usr/sbin/slmodemd --country=ITALY /dev/slusb0
3. Using the modem.
When 'slmodemd' is running this creates PTY (pseudo-terminal) to
emulate modem port device, also this creates symbolic link
like '/dev/ttySL0' (shown at startup).
Config your application to use this link '/dev/ttySL0' (or PTY node
itself) as modem port.
Note: Some application want 'to know' that they are working with
pseudo-terminal and may require additional configurations.
Known application notes:
- 'wvdial' requires option 'Carrier Check = no' in config file
- some versions of 'kppp' may not work properly with devices named
like '/dev/ttySL0'. To workaround this you may create symbolic link
'/dev/modem' ( # ln -s /dev/ttySL0 /dev/modem ) and use this link
as modem device with 'kppp'
- some pci modem devices are declared as COMMUNICATION_MODEM class and
might be caught by other standard drivers - you will see "grabbed
by another driver" warning in dmesg buffer. There is no good way to
"release" it, but as silly workaround you may use 'ungrab-winmodem'
pseudo-driver from.کد:http://linmodems.technion.ac.il/packages/smartlink
Note that you should load it before 'slamr' module.
4. Startup automation.
There are examples of startup scripts in 'scripts' directory.
ALSA mode
=========
ALSA has the built-in modem drivers included in 'alsa-driver' >= 1.0.2
and in Linux kernel >= 2.6.5. Currently there is 'intel8x0m' (snd-intel8x0m)
modem driver, which supports ICH based AC97 modems (MC97).
Recent 'alsa-driver' (>=1.0.6) has also support for NVidia NForce
(snd-intel8x0m) and ATI IXP (snd-atiixp-modem) based modems.
1. Configure your kernel and enable ALSA and ICH based modem support
( 'Device Drivers' -> 'Sound' -> 'Advanced Linux Sound Architecture' ->
'PCI devices' -> 'Intel i8x0/MX440; AMD768/8111 modems' ) .
2. Build and install kernel and modules as usual (make , make modules_install,
etc.). ICH modem driver modem module name is 'snd-intel8x0m'
(if was configured as module).
3. Build application 'slmodemd' with ALSA support. For this in
slmodem-2.9.x dir:
$ cd modem
$ make SUPPORT_ALSA=1
This will build 'slmodemd' with ALSA support. If compilation is failed
review Makefile (near ALSA_SUPPORT condition) and define right library
and/or CFLAGS
4. Use option '--alsa' when running 'slmodemd' and ALSA conventional
device name ('hw:0' or 'hw:1' for instance). If modem support in
the kernel was enabled as module module 'snd-intel8x0m' should be loaded.
Note: Recent version of 'alsa-lib' (>= 1.0.6) has built-in "modem" device
name support ('modem:0', 'modem:1', etc). It is recommended to use
those names with modems (mandatory with ATI IXP modems).
Note: When using ALSA modem driver you don't need to load other
modules ('slamr').
Troubleshooting
===============
If you get an error message during installation/configuration or loading
the modules try to see it in FAQ file.
Please report the problem to your modem provider or to us
(linux-support@smlink.com).
Feedback
========
Please send any feedbacks to Smart Link. See the Smart Link
web site for contact information () or toکد:www.smlink.com
[ برای مشاهده لینک ، با نام کاربری خود وارد شوید یا ثبت نام کنید ] .
دقیقا این مشکل رو دارمکد:http://forum.ubuntu-ir.org/index.php?topic=833.msg5607#msg5607:41:
این فایل رو نصب کن :
برای نصبش روی فایل کلیک راست کن و از منوی kubuntu package menu گزینه install package رو انتخاب کن.کد:http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.68.00.01full/hsfmodem_7.68.00.01full_k2.6.20_15_generic_ubuntu_i386.deb.zip
بعدش برنامه kppp رو از منوی internet اجرا کن. بعد برو به قسمت configure ==> modems ==> new ==> modem و روی query modem کلیک کن ببین نتیجش چی میشه. اگه مودم رو شناخته بود از طریق همون برنامه میتونی یه کانکشن بسازی و به اینترنت وصل بشی.
ممنوننقل قول:
پکیج رو همونطور که گفتید نصب کردم ولی موقع نصب 2 تا warning داد که 2 تا فایل که نمیدونم چی بودن بوسیله برنامه های دیگه در حال استفاده هستن.آخر سر هم که no device detected شد.
query modem رو هم که میزدم : unable to locate a lock file میداد.
:41:
در ضمن وقتی pppk رو اجرا میکنم یه پنجره اخطار باز میشه که میگه فایل resolve.conf پاک شده یا موجود نیست ولی pppk اجرا میشه بدون مشکل.
سلام من می خوام ubuntu 7.4 را نصب کنم ولی قبلش می خواستم بدونم آیا این توزیع از لینوکس می تونه مودم corecess 3112ug مدل usb را شناسایی کنه؟(مودم adsl هستش)
کسی نیست ما را یاری کند؟ای دوستان بشتابید هم اکنون نیازمند یاری سبزتان هستمنقل قول:
دوست عزیز کلا مشکل لینوکس با مودم های اینترنال هست و با مودم های اکسترنال مشکلی ندارندنقل قول:
لینک زیر رو هم نگاهی بکنید:
کد:http://www.technotux.org/html/index.php?name=PNphpBB2&file=viewtopic&p=98491:46:
مودم های گیگابایت تو fedora core حالا مثلا نسخه 7 راحت شناخته میشه یا نه؟
دوباره سلامنقل قول:
باز هم نتونستم مودمم رو نصب کنم تمامی مراحل رو هم انجام دادم انگار تمام کسانی که از آسیاتک این مدل مودم
(corecess 3112ug) رو گرفتن در لینوکس همین مشکل رو دارند از دوستان خواهش می کنم در صورتی که راهی برای این مشکل پیدا کردن یه پیغام به من بزنند منتظرما:19: