مشاهده نسخه کامل
: m.m.m5651
11-07-2013, 23:21
سلام. من میخوام یه QOS برای مودم Asus am602 راه بندازم. تنها کاری که میخوام بکنم هم اینه که سرعت پورت یو اس بی رو بیارم بالاتر از لن. اما خیلی زیاد تنظیمات میخواد. میشه راهنمایی کنید؟
The screen creates a traffic class rule to classify the upstream traffic, assign queuing priority and optionally overwrite the IP header TOS byte. A rule consists of a class name and at least one condition below. All of the specified conditions in this classification rule must be satisfied for the rule to take effect. Click "Save/Apply" to save and activate the rule.
Traffic Class Name:
Enable Differentiated Service Configuration
Assign ATM Priority and/or IP Precedence and/or Type Of Service for the class
If non-blank value is selected for 'Mark IP Precedence' and/or 'Mark IP Type Of Service', the corresponding TOS byte in the IP header of the upstream packet is overwritten by the selected value.
Note: If Differentiated Service Configuration checkbox is selected, you will only need to assign ATM priority. IP Precedence will not be used for classification. IP TOS byte will be used for DSCP mark.
Assign ATM Transmit Priority:
Low Medium High
Mark IP Precedence:
0 1 2 3 4 5 6 7
Mark IP Type Of Service:
Normal Service Minimize Cost Maximize Reliability Maximize Throughput Minimize Delay
Mark 802.1p if 802.1q is enabled on WAN:
0 1 2 3 4 5 6 7
Specify Traffic Classification Rules
Enter the following conditions either for IP level, SET-1, or for IEEE 802.1p, SET-2.
SET-1
Physical LAN Port:
LAN USB
Protocol:
TCP/UDP TCP UDP ICMP
Source IP Address:
Source Subnet Mask:
UDP/TCP Source Port (port or port:port):
Destination IP Address:
Destination Subnet Mask:
UDP/TCP Destination Port (port or port:port):
SET-2
802.1p Priority:
The screen creates a traffic class rule to classify the upstream traffic, assign queuing priority and optionally overwrite the IP header TOS byte. A rule consists of a class name and at least one condition below. All of the specified conditions in this classification rule must be satisfied for the rule to take effect. Click "Save/Apply" to save and activate the rule.
Traffic Class Name:
Enable Differentiated Service Configuration
Assign ATM Priority and/or IP Precedence and/or Type Of Service for the class
If non-blank value is selected for 'Mark IP Precedence' and/or 'Mark IP Type Of Service', the corresponding TOS byte in the IP header of the upstream packet is overwritten by the selected value.
Note: If Differentiated Service Configuration checkbox is selected, you will only need to assign ATM priority. IP Precedence will not be used for classification. IP TOS byte will be used for DSCP mark.
Assign ATM Transmit Priority:
Low Medium High
Mark IP Precedence:
0 1 2 3 4 5 6 7
Mark IP Type Of Service:
Normal Service Minimize Cost Maximize Reliability Maximize Throughput Minimize Delay
Mark 802.1p if 802.1q is enabled on WAN:
0 1 2 3 4 5 6 7
Specify Traffic Classification Rules
Enter the following conditions either for IP level, SET-1, or for IEEE 802.1p, SET-2.
SET-1
Physical LAN Port:
LAN USB
Protocol:
TCP/UDP TCP UDP ICMP
Source IP Address:
Source Subnet Mask:
UDP/TCP Source Port (port or port:port):
Destination IP Address:
Destination Subnet Mask:
UDP/TCP Destination Port (port or port:port):
SET-2
802.1p Priority: